91002-1
  • 点击数:5233
  • 产品类别: 产品分类 连接器 AMP连接器 AMP端子 TE连接器 TE端子 圆形连接器
  • 泰科手动工具 305183,91002-1,TE手动工具,泰科工具,圆形连接器配套

    Connector (Typ)
    Tips
    Insertion Tool
    Handles
    Wire Contact Wire
    © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
    All Rights Reserved
    *Trademark
    TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
    1 of 2
    Instruction Sheet
    TOOLING ASSISTANCE CENTER 1-800-722-1111
    PRODUCT INFORMATION 1-800-522-6752
    This controlled document is subject to change.
    For latest revision and Regional Customer Service,
    visit our website at www.enwer.com LOC B
    408-7347 
    Insertion Tools 91002 and 91002-2 17 OCT 11 Rev A
    Figure 1
    1. INTRODUCTION
    This instruction sheet covers the use of insertion tools
    91002-1 and 91002-2 which are designed to insert pin
    and sockect contacts (which are crimped to small, fragile
    wires) into connectors.
    Read these instructions thoroughly before inserting
    any contacts.
    NOTE
    i
    All dimensions on this instruction sheet are in
    millimeters [with inch equivalents in brackets.]
    2. DESCRIPTION (Figure 1)
    This tweezer-shaped tool features two grooved
    insertion tips for grasping the wire connected to the
    contact and tool handles which assist in applying even
    pressure to the insertion tips.
    The tool is designed for 2.286 mm [.090-in.] maximum
    diameter insulation. but the tool can also be used with
    other types of wire if caution is used during insertion.
    CAUTION
    !
    To determine whether the insertion tool is needed in
    an application, refer to the instruction sheet
    packaged with the product or check with your local
    TE representative.
    3. INSERTION PROCEDURES (Figure 1)
    Insert the contact as follows:
    1. Place the insertion tool over the wire, with tool
    insertion tips behind the contact.
    2. Squeeze tips together to hold the wire and
    contact in position.
    3. Align the contact with back of contact cavity in the
    housing, and insert the contact into housing until it is
    fully seated.
    NOTE
    i
    Some contact cavities will not permit entry of the
    tool tips. If the contact is not fully inserted, grasp
    the wire further back from the contact and push the
    contact in again until it is fully
    408-7347
    Rev A 2 of 2
    5. Pull back lightly on wire to make sure the contact is locked in place.
    4. TOOL INSPECTION
    The tool listed in this instruction sheet should be
    inspected with the information provlded in Figure 2.
    We recommend that you inspect the tool immediately upon arrival in your factory and at regularly scheduled intervals to ensure that the tooling has not been damaged.
    9.525 ± 3.175 [.375 ± .125]7.9248 [.312]76.2 [3.0]2.32 [.093]44.45 [1.75]
    Figure 2
    5. REVISION SUMMARY
    Revisions to this instruction sheet include:
    • Changed company name and logo

     

热门评论
  • 暂无信息

验证码: 验证码,看不清楚?请点击刷新验证码

电话:0512-86661229/66185650 地址:苏州工业园区通和路浦田工业园11-1号

版权所有 copyright(c)2009-2010 苏州恩威电子科技有限公司 苏icp备12003885号